超聲波清洗機設備的應用范圍越來越廣，經過各種改進和改進的新型超聲波清洗機設備將取代市場上的舊設備，超聲波清洗機正在向兩個方面發展。 其一，各種類型的多缸或傳動鏈式或升降式超聲波清洗機相繼上市；其二，低頻超聲波清洗機向高頻超聲波清洗機的發展：

The application range of ultrasonic cleaning machine equipment is becoming increasingly wide, and new types of ultrasonic cleaning machine equipment that have undergone various improvements and improvements will replace old equipment in the market. Ultrasonic cleaning machines are developing in two directions. Firstly, various types of multi cylinder or transmission chain or lifting ultrasonic cleaning machines have been launched successively; Secondly, the development of low-frequency ultrasonic cleaning machines towards high-frequency ultrasonic cleaning machines:

當然，超聲波清洗機在使用中也有可能發生常見問題。 例如，在超聲波振子暴露在濕氣中的情況下，可以用兆歐表檢查與換能器連接的插頭，通過檢查絕緣電阻值可以判斷基本的狀況，一般要求絕緣電阻在5兆歐表以上。 如果達不到該絕緣電阻值，通常換能器是濕的，所以可以將換能器整體放入烤箱，設定在溫度100度左右，干燥3小時，或者使用電吹風去除濕氣直到電阻值正常。

Of course, ultrasonic cleaning machines may also encounter common problems during use. For example, when the ultrasonic oscillator is exposed to moisture, a megohmmeter can be used to check the plug connected to the transducer. By checking the insulation resistance value, the basic condition can be determined, and the insulation resistance is generally required to be above 5 megohmmeters. If the insulation resistance value cannot be reached, the transducer is usually wet, so the transducer can be placed as a whole in an oven, set at a temperature of about 100 degrees Celsius, dry for 3 hours, or use a hair dryer to remove moisture until the resistance value is normal.

振子著火，陶瓷材料破裂時，可以結合肉眼和兆歐表進行檢查。 一般來說，作為應急措施，可以分別分離破損的振子，不影響其他振子的正常使用。 振子脫膠，我們的換能器采用粘接。 是螺絲緊固的雙重保證技術，在普通情況下不會發生這種情況。 不銹鋼的振動面上有孔，一般的轉換器在充分使用10年后，振動面有時會有孔。 日常生活中也需要清潔眼鏡、清潔精密儀器和工件等超聲波清洗機。 多功率超聲波清洗機之所以在許多行業使用，不僅清洗適應性強、清洗各種工件的功率大，而且對前板的尺寸和任務頻率也有適應性，設備能夠在各種環境條件下持續工作。

When the oscillator catches fire and the ceramic material ruptures, visual inspection and a megohmmeter can be used for inspection. Generally speaking, as an emergency measure, damaged oscillators can be separated separately without affecting the normal use of other oscillators. The oscillator is debonded, and our transducer is bonded. It is a double guarantee technology for screw fastening, and this situation will not occur under normal circumstances. Stainless steel has holes on the vibration surface, and typical converters may sometimes have holes on the vibration surface after 10 years of full use. In daily life, it is also necessary to clean glasses, precision instruments, and workpieces using ultrasonic cleaning machines. The reason why high-power ultrasonic cleaning machines are used in many industries is not only because they have strong cleaning adaptability and high cleaning power for various workpieces, but also because they are adaptable to the size and task frequency of the front plate. The equipment can continue to work under various environmental conditions.

一些超聲波清洗產品以空化為技術中心，通過聲壓振動調節壓力能量。 該多功能超聲波清洗機可根據實際情況停止多功率調節，在確保侵蝕力的基礎上，在短時間內破壞氣泡，達到快速、清潔的目的。

Some ultrasonic cleaning products focus on cavitation technology and regulate pressure energy through sound pressure vibration. This multifunctional ultrasonic cleaning machine can stop multi power adjustment according to the actual situation, and on the basis of ensuring erosion force, it can quickly destroy bubbles and achieve the goal of fast and clean.

多動力、高質量的超聲波清洗機能夠消除深度清洗效果差的瓶頸，進行精細調整后，氣泡上升到大裂縫，完全停止清洗，迅速剝離后，凈化后的物質難以附著在工件上，因此凈化物質的殘留率低

A multi power, high-quality ultrasonic cleaning machine can eliminate the bottleneck of poor deep cleaning effect. After fine adjustment, bubbles rise to large cracks and completely stop cleaning. After rapid peeling, the purified substance is difficult to adhere to the workpiece, so the residual rate of the purified substance is low

感謝您的閱讀，此文的文章來源：超聲波清洗機更多的內容和問題請點擊： http://m.0359hd.com我們會繼續努力的為您提供服務，感謝您的支持！

Thank you for reading. The source of this article is: Ultrasonic Cleaning Machine. For more information and questions, please click: http://m.0359hd.com We will continue to work hard to provide you with services. Thank you for your support!